CAT D5K2 LGP 70774

SOLD
"

MACHINE KEY DETAILS

Make:
Caterpillar
Model:
D5K2 LGP
Stock No:
70774
Year:
2019
Hours:
4666
Location:
Southampton
Weight:
9,522 KGS
HP:
104 HP
Back to Current Stock

PAT Blade, Trimble ARO, Rippers available at an additional cost

View Full Inspection Report

ENGINE
Blow By
Minimal
Knocking
No knocking
Air Cleaners
Good
Any Smoke
Minimal to none
Oil Or Fuel Leaks
None visible
General Running Condition
Runs well
TRANSMISSION
Gear Change
HST speed control works well
Steering
Responsive
Oil Leaks
None visible
Is The Transmission Noisy?
No
Torque Converter
No juddering
Controls
Good controls
General Running Condition
Runs well
UNDERCARRIAGE
Shoe Width
660mm
Shoe Height
40mm, 70%
Rail Height
105mm, 90%
Any Signs Of Link Failure
No
Average Diameter Of Pins And Bushings
59mm, 90%
Have Pins Been Turned On Chains
No
Sprockets
16 - 17mm Tips, 75mm Gape. 90%
UNDERCARRIAGE - IDLERS
Left Side Front Idler
50mm x 22mm, 90%
Right Side Front Idler
50mm x 22mm, 90%
UNDERCARRIAGE - TOP ROLLERS
Left Side 1st Roller
164mm x 163mm, 90%
Right Side 1st Roller
164mm x 164mm, 90%
UNDERCARRIAGE - BOTTOM ROLLERS
Roller 1
170mm x 170mm, 90%
Roller 2
172mm x 172mm, 90%
Roller 3
172mm x 172mm, 90%
Roller 4
172mm x 172mm, 90%
Roller 5
172mm x 171mm, 90%
Roller 6
171mm x 170mm, 90%
Roller 7
Visual only, 90%
CAB
Cab Mounts - Any Wear?
Minimal
Any Wiring For Laser System?
Yes
Back Up Alarm
Loud and clear
Battery Isolator Switch
Manual
Lights
All working
Wipers
All wipers and washers work
Heater
Good heat
A/C
Good cold A/C
Seat Condition
Good condition, small air leak
Cladding Condition
Good condition
Floor Matt Condition
No wear or tears
Seat Belt
Working as should
Mirrors
Rear view only, undamaged
Horn
Loud and clear
Cab Mounts
Good
Cab Glass Condition
Good condition
Cab Glass Have Any Cracks
No damage
Any Perspex Fitted
None fitted
Steps And Grab Handles Secure?
Secure and undamaged
BLADE
Blade Type
PAT 6 Way
Blade Width
3200mm
Blade Height
1020mm
Main Lift Rams, Wear In Pins
L/H: 2mm x 1mm. R/H: 2mm x 1mm
Pitch Ram Wear
L/H: 3mm x 1mm. R/H: 3mm x 1mm
Tilt Ram Wear
7mm x 2mm
Link Ram Wear
1mm x 1mm
Ball Joint Wear
10mm
C Frame Wear
5 - 7mm x 5 - 7mm
Face / Moldboard
Good condition, no dents
Cutting Edges Condition
45mm Left
Have Cutting Edges Been Turned
No
General Blade Condition
ok
PAINT & DECALS
Any Damage To Panels
Off side compartment door
Paint Condition
Ok, little faded
Any Rust Patches
Track frames and back of blade
Condition Of Decals
To be replaced

Enquire online

Compare to other Machines

make
Ashland
model
155TS2
stock no
year
2017
hours
location
weight
hp
More Info
make
HAMM
model
H12i
stock no
70769
year
2022
hours
67
location
Southampton
weight
11,715 KGS
hp
114 HP
More Info

Subscribe

Find out when new models come in